For some reason, there was a mismatch between the setting (decibel) and the audiohw code (centicel). This resulted in a gain divided by 10. This may explain why some people experienced low volume with the mic on the fuze+. Change-Id: I138ac18dd93c36f43a7dfce735efc826405c598c
Also clarity parts of the code. The old code suffered from two defects: - it was very unclear because it made changes to whole registers (using as3514_write) instead of fields (using as3514_set/clear/write_masked). Also the routing code was spread accross several functions which made it hard to follow. - it did not properly reroute audio on monitor changes. In particular, the following could happen: when switching from DAC to radio, the code would fail to clear SUM_off, resulting in a weird situation where the main mixer was off (SUM_off) but the headphone where using the main mixer as input. Incredibly this worked anyway (at least on AMSv2 and YP-R0) but resulted in strange volume gaps between DAC and radio mode. Change-Id: I7826835fdb59c21f6483b223883ca9289e85caca
Some old code made the assumption that CONFIG_CPU == AS3525v2 if and only if HAVE_AS3543, which is not true on targets like the Samsung YP-R0. This fixes several issues on such targets like a huge volume gap between -39dB and -40dB and a volume artificially capped at -72dB instead of -82dB. Change-Id: Ib1c883ac593c0c3ce5e2bf4eb408924ce5f5ad93
Change-Id: I99fe6d09b15689e5dd0179714bbe363aed922d10
There are a couple of power saving options that can be selected using defines, they configure the CODEC in a different way than OF does: MONO_MIC: jack microphone is connected to left channel, disabling right channel saves ~1 mW, there is no reason to not to do it. BYPASS_PGA: this option only applies to the line-in, OF does not bypass the PGA and configures it to 0 dB gain. At the beginning, this patch was written based on CODEC datasheet, bypassing PGA because it saves power and incrementes dinamic range ~1dB, i have used this setup for a while without problems. Finally this option was disabled at the last minute, i decided to do it after reviewing the OF and realizing that CS42L55 datasheet recommends to bypass the PGA only if the HW includes a couple of capacitors (see Typical Connection Diagram, Note 4), at this moment i don't know if Classic includes these capacitors (probably not). Anyway, i am not able to tell the difference listening to voice recodings. TODO: - Use variable PGA gain for jack microphone (it is fixed to +12 dB. as OF does). - I am not a fan of having lots of unused #define options, these could be useful for a generic driver but actually this driver is Classic oriented, i am not sure if it could be considered disirable to eliminate them in the final version. Change-Id: I3dadf2341f44d5e13f3847e6c9de4a76cd6f0918
Change-Id: Ifc82ac1051ed05527393838d8aa93bde65287b5d
Fix regressions introduced by 42219b6e7 Change-Id: I1f3edb5f269f60e9431b45a43c4370836ecac733
Reorganization - Separated iBasso devices from PLATFORM_ANDROID. These are now standlone hosted targets. Most device specific code is in the firmware/target/hosted/ibasso directory. - No dependency on Android SDK, only the Android NDK is needed. 32 bit Android NDK and Android API Level 16. - Separate implementation for each device where feasible. Code cleanup - Rewrite of existing code, from simple reformat to complete reimplementation. - New backlight interface, seperating backlight from touchscreen. - Rewrite of device button handler, removing unneeded code and fixing memory leaks. - New Debug messages interface logging to Android adb logcat (DEBUGF, panicf, logf). - Rewrite of lcd device handler, removing unneeded code and fixing memory leaks. - Rewrite of audiohw device handler/pcm interface, removing unneeded code and fixing memory leaks, enabling 44.1/48kHz pthreaded playback. - Rewrite of power and powermng, proper shutdown, using batterylog results (see http://gerrit.rockbox.org/r/#/c/1047/). - Rewrite of configure (Android NDK) and device specific config. - Rewrite of the Android NDK specific Makefile. Misc - All plugins/games/demos activated. - Update tinyalsa to latest from https://github.com/tinyalsa/tinyalsa. Includes - http://gerrit.rockbox.org/r/#/c/993/ - http://gerrit.rockbox.org/r/#/c/1010/ - http://gerrit.rockbox.org/r/#/c/1035/ Does not include http://gerrit.rockbox.org/r/#/c/1007/ due to new backlight interface and new option for hold switch, touchscreen, physical button interaction. Rockbox needs the iBasso DX50/DX90 loader for startup, see http://gerrit.rockbox.org/r/#/c/1099/ The loader expects Rockbox to be installed in /mnt/sdcard/.rockbox/. If /mnt/sdcard/ is accessed as USB mass storage device, Rockbox will exit gracefully and the loader will restart Rockbox on USB disconnect. Tested on iBasso DX50. Compiled (not tested) for iBasso DX90. Compiled (not tested) for PLATFORM_ANDROID. Change-Id: I5f5e22e68f5b4cf29c28e2b40b2c265f2beb7ab7
This change reduces noise and distortion very slightly at higher volumes. Change-Id: I1a2eb160c2956de90764c0bb11677fdac8d96dec
The port to for this two targets has been entirely developped by Ilia Sergachev (alias Il or xzcc). His source can be found at https://bitbucket.org/isergachev/rockbox . The few necesary modifications for the DX90 port was done by headwhacker form head-fi.org. Unfortunately i could not try out the final state of the DX90 port. The port is hosted on android (without java) as standalone app. The official Firmware is required to run this port. Ilia did modify the source files for the "android" target in the rockbox source to make the DX port work. The work I did was to separate the code for DX50 (&DX90) from the android target. On this Target Ilia used source from tinyalsa from AOSP. I did not touch that part of the code because I do not understand it. What else I changed from Ilias sources besides the separation from the target "android": * removed a dirty hack to keep backlight off * changed value battery meter to voltage battery meter * made all plugins compile (named target as "standalone") and added keymaps * i added the graphics for the manual but did not do anything else for the manual yet * minor optimizations known bugs: * timers are slowed donw when playback is active (tinyalsa related?) * some minor bugs Things to do: * The main prolem will be how to install the app correctly. A guy called DOC2008 added a CWM (by androtab.info) to the official firmware and Ilia made a CWM installation script and a dualboot selector (rbutils/ibassoboot, build with ndk-build). We will have to find a way to install rockbox in a proper way without breaking any copyrights. Maybe ADB is an option but it is not enable with OF by default. Patching the OF is probably the way to go. * All the wiki and manual to build: needed: android ndk installed, android sdk installed with additional build-tools 19.1.0 installed ./tools/configure select iBasso DX50 or iBasso DX90 make -j apk the content of rockbox.zip/.rockbox needs to be copied to /system/rockbox/app_rockbox/rockbox/ (rockbox app not needed) the content of libs/armeabi to /system/rockbox/lib/ (rockbox app needed) The boot selector is needed as /system/bin/MangoPlayer and the iBasso app as /system/bin/MangoPlayer_original. There is also the "vold" file. The one from OF does not work with DX50 rockbox (DX90 works!?), the one from Ilia is necessary. Until we have found a proper way to install it, it can only be installed following the instructions of Ilia on his bitbucket page, using the CWM-OF and his installation script package. Change-Id: Ic4faaf84824c162aabcc08e492cee6e0068719d0 Reviewed-on: http://gerrit.rockbox.org/941 Tested: Chiwen Chang <rock1104.tw@yahoo.com.tw> Reviewed-by: Michael Giacomelli <giac2000@hotmail.com>