rockbox/firmware/drivers/rtc/rtc_imx233.c, branch master My Rockbox tree imx233: generate register headers using headergen_v2 and update code for it 2016-05-28T14:49:22+00:00 Amaury Pouly amaury.pouly@gmail.com 2016-05-24T19:29:56+00:00 eac1ca22bd4a6c1849880d0f8b6764befb60bc21 NOTE: this commit does not introduce any change, ideally even the binary should be almost the same. I checked the disassembly by hand and there are only a few differences here and there, mostly the compiler decides to compile very close expressions slightly differently. I tried to run the new code on several targets to make sure and saw no difference. The major syntax changes of the new headers are as follows: - BF_{WR,SET,CLR} are now superpowerful and allows to set several fileds at once: BF_WR(reg, field1(value1), field2(value2), ...) - BF_CS (use like BF_WR) does a write to reg_CLR and then reg_SET instead of RMW - there is no more need for macros like BF_{WR_,SET,CLR}_V, since one can simply BF_WR with field_V(name) - the old BF_SETV macro has no trivial equivalent and is replaced with its its equivalent for BF_WR(reg_SET, ...) I also rename the register headers: "regs/regs-x.h" -> "regs/x.h" to avoid the redundant "regs". Final note: the registers were generated using the following command: ./headergen_v2 -g imx -o ../../firmware/target/arm/imx233/regs/ desc/regs-stmp3{600,700,780}.xml Change-Id: I7485e8b4315a0929a8edb63e7fa1edcaa54b1edc 
NOTE: this commit does not introduce any change, ideally even the binary should
be almost the same. I checked the disassembly by hand and there are only a few
differences here and there, mostly the compiler decides to compile very close
expressions slightly differently. I tried to run the new code on several targets
to make sure and saw no difference.

The major syntax changes of the new headers are as follows:
- BF_{WR,SET,CLR} are now superpowerful and allows to set several fileds at once:
  BF_WR(reg, field1(value1), field2(value2), ...)
- BF_CS (use like BF_WR) does a write to reg_CLR and then reg_SET instead of RMW
- there is no more need for macros like BF_{WR_,SET,CLR}_V, since one can simply
  BF_WR with field_V(name)
- the old BF_SETV macro has no trivial equivalent and is replaced with its
  its equivalent for BF_WR(reg_SET, ...)

I also rename the register headers: "regs/regs-x.h" -> "regs/x.h" to avoid the
redundant "regs".

Final note: the registers were generated using the following command:
./headergen_v2 -g imx -o ../../firmware/target/arm/imx233/regs/ desc/regs-stmp3{600,700,780}.xml

Change-Id: I7485e8b4315a0929a8edb63e7fa1edcaa54b1edc
sonynwz: fix time handling 2013-09-26T15:01:44+00:00 Amaury Pouly amaury.pouly@gmail.com 2013-09-26T15:01:44+00:00 0897794f445c1cbe5c0da4fb95d203491c3871a7 Be consistent with the OF and use RTC PERSISTENT2 as offset Change-Id: Ic8b970cbc4096d1f4efa0380a3af51c93484fe58 
Be consistent with the OF and use RTC PERSISTENT2 as offset

Change-Id: Ic8b970cbc4096d1f4efa0380a3af51c93484fe58
imx233: implement alarm wake up 2013-07-01T22:45:00+00:00 Amaury Pouly amaury.pouly@gmail.com 2013-07-01T22:36:21+00:00 d8024df1052966aa554424d88712244ae5978f2a This adds the application part of alarm wake up. On some targets like the Fuze+, it will also require a bootloader change to make sure that the device doesn't power down on alarm wake up (for example on the Fuze+ the bootloader requires the power button to be hold sufficiently long, thus preventing alarm wake up to work) Change-Id: I5d01957852355fddbd48110d3d75a5533f07879e 
This adds the application part of alarm wake up. On some targets
like the Fuze+, it will also require a bootloader change to make
sure that the device doesn't power down on alarm wake up (for
example on the Fuze+ the bootloader requires the power button to
be hold sufficiently long, thus preventing alarm wake up to work)

Change-Id: I5d01957852355fddbd48110d3d75a5533f07879e
zenxfi3: RTC is used in same was as in fuze+, using seconds-since-1970 plus an offset 2012-05-26T22:16:40+00:00 Bertrik Sikken bertrik@sikken.nl 2012-05-26T22:14:42+00:00 fca9e7bf8d48f2fcc4c8b21cc29aabf2ce053900 Change-Id: Iab2e6e15c790c26d3bf2679e9f965a409d162783 
Change-Id: Iab2e6e15c790c26d3bf2679e9f965a409d162783
imx233: move rtc init from drivers/ to firmware/ 2012-05-19T10:57:42+00:00 Amaury Pouly amaury.pouly@gmail.com 2012-05-19T10:57:04+00:00 692338629ba1d21a4f78d75bd4baa2f0ff74960e Change-Id: Id816987a4bb1191d5c9cf8a85c51d75fbb2da7c8 
Change-Id: Id816987a4bb1191d5c9cf8a85c51d75fbb2da7c8
Convert IMX233 RTC driver (used in fuze+) to use mktime and gmtime 2012-03-13T18:27:55+00:00 Bertrik Sikken bertrik@sikken.nl 2012-03-11T14:59:55+00:00 47115ba8347f857fa5f59dc4326127e5849ea4eb Change-Id: Ie71d495509a81db5e02078398f5d722c00136072 
Change-Id: Ie71d495509a81db5e02078398f5d722c00136072
imx233/fuze+: implement rtc (time only, alarm still to implement) 2011-12-31T13:35:45+00:00 Amaury Pouly pamaury@rockbox.org 2011-12-31T13:35:45+00:00 094e62a528e95677a16a9465a1decfdc045e7197 git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31473 a1c6a512-1295-4272-9138-f99709370657 
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31473 a1c6a512-1295-4272-9138-f99709370657
imx233/fuze+: huge rework 2011-07-23T11:45:22+00:00 Amaury Pouly pamaury@rockbox.org 2011-07-23T11:45:22+00:00 eb90d956935019f577311ebc7aec3a7898d76019 - enable MMU -rework lcd frame buffer - add rtc/adc/power stubs (or not) - fix a few MMC related defines (hopefully) - implement cache handling for DMA - more SD work - add keymap (based on clip) - add virtual buttons - update linker scripts - big step toward apps actually compiling git-svn-id: svn://svn.rockbox.org/rockbox/trunk@30200 a1c6a512-1295-4272-9138-f99709370657 
- enable MMU
-rework lcd frame buffer
- add rtc/adc/power stubs (or not)
- fix a few MMC related defines (hopefully)
- implement cache handling for DMA
- more SD work
- add keymap (based on clip)
- add virtual buttons
- update linker scripts
- big step toward apps actually compiling

git-svn-id: svn://svn.rockbox.org/rockbox/trunk@30200 a1c6a512-1295-4272-9138-f99709370657